Hoyt St. Puck Remote Design Contest Voting

[BillGordon]

Hey all-

After a few months and some great submissions, it’s time to decide who will be getting their Puck design printed in glorious MultiJet Fusion Nylon!

Here are the official submissions in no particular order:

[Puck Design Contest Entry] Bat Wing

Hi friends! New to this forum, thought I would play around with Fusion 360 a bit and found out its my new favorite 3D design tool. Made my own version of the puck case shaped more like your natural grip for easy cramp free riding. I have been testing this version for a few days now and it almost feels like it disappears in my hand. Try it out if you want and lemme know what you think! [IMG_20210312_180430] [IMG_20210312_180423] [IMG_20210312_180456] Bat Wing

DougM's Hoyt Pro [Puck Design Contest Entry]

I wish I had done a build log for this remote. I did a lot of video around it, so will be putting together a build video that I’ll put up on Youtube and link here, but it won’t be for a while (the remote is tangential to another project). Presenting: DougM’s Hoyt Pro [image] The thing I think could use improvement in the Hoyt design is that the cylindricity of the remote doesn’t give you very positive location feedback in your hand - so you have to carefully adjust how you hold it so the th…

The Puck’n’Trigger mod [Puck Design Contest Entry]

As already mentioned on @Glyphiks thread, we had the same brilliantly stupid idea to create a puck shell that turns it into a trigger remote. [Trigger Puck] So far, I have re-built the puck guts casing, added a trigger to the thumb wheel, and mocked up a pistol grip to the back shell [IMG_20210211_152336544] [IMG_20210211_152130688] [IMG_20210211_153043496] Next step is working on the ergonomics by adapting the angle of the trigger and of course deciding on how to best adapt the puck g…

Poastmote Round 2! 2poast2mote [Puck Design Contest Entry]

Aight hoes, I did her again, this time with some improvements! some-ish volume, but I made it more comfy to hold I made a nubby bubby wheel just for 2.0, but the buttons stayed the saame Hopefully it’s a bit more big hand friendly! It’s ages easier to print with less weird geometries that could cause some imperfections can’t forget! she got a lanyard hole now! you know how it be uwu As always, feedback is welcome! [Screen Shot 2025-03-22 at 5.59.28 PM] [Screen Shot 2025-03-22 at 5.59.40…

[Puck contest entry] Round 2 mini-Puck: The nugPuck

Alright, I went back to the drawing table and redesigned my mini-Puck. I’ve been trying to learn Fusion 360, and I was inspired by some of the other contest entries to learn more about modeling. My first version used really simple techniques, but here I got into T-spine modeling. Using T-spline I was able to make a far more ergonomic and better looking enclosure. Also, I was also able to maintain the ambidexterity of the original Puck. This is important to me because I’m a southpaw and I let a l…

A reminder about what the winners get:

Rather than doing tiered prizes, each of the 3 winners will receive their own Remote Shell design (complete with PuckGuts + Receiver) printed professionally via MultiJet Fusion Nylon process (in up to 2 different colors of their choice) + additional Shell sets of the other 2 winning designs via the same printing process.

With all that laid out, let’s vote!

The Hoyt St Puck Design Contest

• Poasttoast-2poast2mote
• Tomiboi-nugPuck
• R32Tech-Bat Wing
• DougM-Hoyt Pro
• Redeye-Puck 'n Trigger

Voting will be live for seven days. (FreeSK8 staff will not be voting.) Good luck all!

[xsynatic]

This contest made me want a puck so bad.

[Kilow]

This was a tough one to choose between the poastmote and the mug for me. The very gripable to the little pocket remote

[BillGordon]

Would have loved to have your great design in the mix, but respect your reasoning.

[glyphiks]

Fuck i need to get printing.

[Kilow]

Really appreciate having the 3D models for the puck and the gotchi’s. We would have a hard time without out them or getting to see all the work Andrew did on the puck puck Bruce

[Nacho]

This is hard

[BillGordon]

@Nacho

This is hard

I want points for not responding to this like a child.

[Nacho]

They are all amazing I like one a little bit more because of a cool feature

[glyphiks]

I absolutely commend you for this. Well done sir.

[Cfelzien]

It was tomibois nugs that did it for me. Felt cute. Might delete later.

[Linny]

@Kilow your design didn’t make it thru?

[Lobap]

I really like the shape of @R32Tech design

[Kilow]

I felt that messing with puck PCB might have been a bit risky so I didn’t enter it into the competition. I did have fun working on it, so I wanted to share what I did and post.

I am also not so sure it would be suitable for a nylon print. I quoted it at shapeways and it was expensive. Maybe changing the internal design would help. The grip is mostly solid and I wonder if a shelled design would be better.

[xsynatic]

@DougM Yours is the first one I’m going to print once i have a puck in my hand. It looks the closest to what I’m used to.

[poastoast]

after official voting, will we know which remote each freesk8 staff would’ve voted for?

[glyphiks]

My ‘not allowed to vote’ vote went to the poastmote!

Really enjoyed following the design process in the telegram chat, love the feel of it in my hand, and also gets bonus points for not using the puck guts files to model from!

Also really happy that my suggestion of the ‘uwu’ design made it onto the buttons